When your Jeep Renegade requires an oil change, the oil warning light will illuminate. Although performing the task yourself saves money, you will need to manually reset the oil light to prevent premature notifications in the next cycle.
This guide will walk you through the process, showing you how to quickly reset the oil indicator on your Renegade jeep without any special tools.
How To Reset Oil Light On The Jeep Renegade
If you have recently changed the oil in your Jeep Renegade but the oil change light remains on, you’ll need to manually reset it. Follow the instructions below to successfully reset the oil light on your Jeep Renegade.
Steps to Reset the Oil Light
- Apply the Parking Brake: Ensure your vehicle is secure by applying the parking brake.
- Position the Gear: The gear changer should be in the park position.
- Set the Engine in ON Position: Without starting the vehicle, turn the ignition so the engine is in the ON position.
- Press the Gas Pedal: Depress and release the gas pedal three times in quick succession.
- Turn the Ignition Off and On: Turn the ignition to OFF, then back to the ON position.
- Confirm the Reset: Check to see if the oil change light is no longer illuminated on the dashboard.
If the oil change light does not reset on the first try, you may need to repeat the process. Ensure the steps are followed accurately and that the gas pedal is fully depressed and released three times within a span of 10 seconds.
Remember, the oil change light is a reminder to maintain the health of your vehicle’s engine. You should always reset this light after you’ve changed the oil, not simply to turn the light off.
These steps should work for most models of the Jeep Renegade, but always refer to your vehicle’s owner’s manual for model-specific information. If you continue to have issues with the oil change light, consider taking your vehicle to a certified automotive technician for a diagnosis.
What Causes The Jeep Renegade’s Oil Light To Come On?
The oil light on your Jeep Renegade serves as a crucial indicator of potential issues with your vehicle’s engine oil. Several factors can cause this light to illuminate:
- Low Oil Pressure: If your vehicle’s oil pressure is too low, the oil light will turn on. Low oil pressure can occur due to a lack of sufficient oil, a failing oil pump, or blocked oil passages.
- Low Oil Level: A low level of engine oil can cause the oil light to come on. This can be a result of a leak or the oil simply being used up over time.
- Faulty Oil Pressure Sensor: Sometimes, the oil light might come on due to a faulty oil pressure sensor. The sensor may give false readings, causing the oil light to turn on even when there is no actual problem with the oil pressure or level.
- Overheated Engine: If your engine overheats, it can cause the oil to break down and lose its viscosity, thus reducing its lubricating properties. This can trigger the oil light.
- Worn-out Engine: As your vehicle ages, wear and tear can cause the engine’s parts to loosen, which can cause oil to leak into areas it shouldn’t be, reducing the overall oil pressure and triggering the oil light.
It’s important to not ignore the oil light when it comes on. If it does illuminate, it’s advisable to immediately check your oil level and pressure. If everything seems in order but the light is still on, it’s best to take your vehicle to a mechanic for a thorough inspection to avoid potential engine damage.
Also Read: Does Carmax Buy Motorcycles?
Changing Oil For The Jeep Renegade
Now that you understand how to reset the oil service light, let’s discuss the steps for changing the oil. You should never reset the maintenance light without performing the necessary service as it could lead to serious engine damage.
The Jeep Renegade’s engine uses synthetic oil, and the exact type required can be determined by checking the owner’s manual or the engine’s oil cap. The most common oil types used include 0W-20, 10W-30, and 5W-40.
The oil is held in place by a single nut on the oil pump. You’ll need just one spanner to disassemble this nut if you’re not changing the oil filter. However, purchasing an oil filter wrench is recommended as manually removing the filter can be quite challenging.
Follow these steps to change the oil and oil filter:
- Warm up the engine to allow the oil to flow more easily.
- Put on protective gloves and place an oil drain pan under the oil tank.
- Using a wrench, remove the nut holding the oil in place.
- Once the oil has drained, use an oil filter wrench to remove the oil filter.
- Install the new filter and tighten the oil drain nut.
- Open the hood and remove the oil cap, then add the correct amount of oil.
- Run the engine for thirty seconds, check the oil levels, and add more if necessary.
- Slowly remove the oil drain pan and pour the old oil into its original container.
- Dispose of the old oil at a recycling center.
Frequently Asked Questions
Here are some commonly asked questions regarding the oil life reset process and their answers.
How can the oil life of a Jeep be reset?
Navigate to the “Oil Life” under “Vehicle Info” in the embedded display, and hold down the “OK” button. This will reset the oil life gauge to 100%.
How can I turn off the dashboard’s “Change Oil” light?
Turn on the ignition, fully depress the accelerator and brake pedals simultaneously for three seconds.
Where is the oil change reset button?
The reset button is typically located on the front side of the device, close to or next to the power button.
What happens if the oil life is not reset?
Your vehicle may notify you to change oil more often than necessary.
Does the oil life need to be reset after an oil change?
Yes, your car’s engine oil life calculation system needs to be reset every time you change the oil.
Conclusion
Resetting the oil warning light on a Jeep Renegade is a straightforward process that takes only a few seconds. Keep in mind to always change the oil when required, and not simply reset the warning light. If you need more assistance with Jeep repair and maintenance, feel free to explore our other guides.